We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
Photodetectors are useful because they convert photons into electrical signals. However, certain shortcomings in terms of wide-angle imaging for spherical-shaped photo sensors have been reported. The study published in the journal Nature Communications discusses a novel 2D quasi-perovskite hemispherical photonic sensor optimized for wide-angle imagery.
Study: Spray-coated perovskite hemispherical photodetector featuring narrow-band and wide-angle imaging . Image Credit: MOLPIX/Shutterstock.com
Highly sophisticated photo-detection sensors monitoring specific wavelengths have been employed in a variety of industries, especially perioperative surgical treatments, remote monitoring systems, and facial recognition systems.
However, the major hurdle for planar photodetectors is their limited imaging angle, which is only 60 degrees. The fisheye lens increased this value to around 180°, but the complicated optical pathway added to the cost of the embedded wide-angle sensitive detector. Considering these problems, the use of spherical sensors was necessary.
A hemispherical-shaped sensor, primarily inspired by fisheye and compound-eye design, provides an adequately wide visual angle. However, certain challenges still need to be addressed.
The major hurdle is the deposition of a soluble active layer on the non-planar platforms for fabricating photodetectors operational on a specific wavelength along with a broad viewing angle. Additionally, the cost issues and low deposition speed associated with gas vapor deposition of semiconductor substances on the substrate surface must be addressed.
Spray-coating is an established technique that has had widespread application in automotive varnishing and marine corrosion inhibition treatment. This low-cost solution technique deposits multilayer thin films on irregularly shaped surfaces optimally. Unlike spin coating or other previous processes, spray coating is not constrained by the geometry of the platform.
Furthermore, spray-coating is a pneumatically operated coating technique, and discharged solvents typically vaporize extremely quickly before accumulating on the surfaces. Consequently, the succeeding film doesn't disintegrate the preceding coatings.
Quasi-2D perovskites are made up of alternating inorganic and organic layers. The blend of superior charge carrier dynamics (3-D perovskite material benefits) and the exceptional stability of the 2-D counterpart is a primary reason for their excessive utilization in modern electronics.
Their distinct photoelectric features, variable energy band gap, and defect endurance make them appealing for use in photovoltaic devices, light-emitting diodes (LEDs), X-ray scanners, and optoelectronic devices.
Perovskite coatings fabricated via spray coating techniques for photovoltaic applications have been reported recently. Its most significant benefit is the homogeneous coating of photoactive layers on randomly oriented substrates, which has never been thoroughly explored.
The article describes spray coated spherical perovskite photonic sensor made of phenyl ethyl ammonium/formamidinium lead halide (PEA2FAn-1PbnX3n+1). The researchers utilized the Perovskite formulations to regulate the crystallization rate. Cyclic spray-coating and the solution concentration were used to control the coating thickness from a few nanometers to hundreds of micrometers.
For consistent layer thickness, the substrate was rotated during spray coating. Before deposition, hemispherical platforms with thoroughly cleansed edges were placed on a hot plate. High-speed nitrogen (N2) gas was used to exfoliate the surfaces and expedite the crystallization of the coatings. To enhance crystallization quality, the sheets were ultimately thermally treated. The films' surfaces were refined to create a smooth and compact coating with minimal surface flaws.
Chromium (Cr) electrodes were mounted on commercialized hemispherical glass substrates to increase surface adherence to build a hemispherical device.
The poor conductance of the bottom Cr electrodes contributed to a lower cut-off ratio of hemispherical devices when compared to planar devices. The photocurrent of the device was measured about the incident light angle to investigate the wide-angle detection accuracy.
Upon diverse light incidence angles between 0° and 90°, the hemispherical sensor displayed autonomous photon energy. However, because of the restricted light absorption at slanted orientations, the photocurrent of the planar sensor proportionally reduced with the incident angle.
A model of a swan was used for imaging studies. A clear image of a swan was captured in the right panel when the object was placed at a viewing angle between 90° and -52°. The image had the same viewing angle range of -8° to 30° and had a spatial resolution of 1.78 lp mm-1. The benefits of a hemispherical photocell are shown by the fact that the planar device completely lost signal at a viewing angle of about 90 degrees and could only capture a half-image of the swan.
In short, a rapid spray-coating procedure was used to create a perovskite hemispherical photodetector that can execute lens-free scanning at nearly 180°, considerably decreasing the reliance on complex optical components.
More from AZoM: How are Bioplastics Made?
Feng, X. et al. Spray-coated perovskite hemispherical photodetector featuring narrow-band and wide-angle imaging. Nat Commun. 13. 6106. Available at: https://doi.org/10.1038/s41467-022-33934-1
Disclaimer: The views expressed here are those of the author expressed in their private capacity and do not necessarily represent the views of AZoM.com Limited T/A AZoNetwork the owner and operator of this website. This disclaimer forms part of the Terms and conditions of use of this website.
Ibtisam graduated from the Institute of Space Technology, Islamabad with a B.S. in Aerospace Engineering. During his academic career, he has worked on several research projects and has successfully managed several co-curricular events such as the International World Space Week and the International Conference on Aerospace Engineering. Having won an English prose competition during his undergraduate degree, Ibtisam has always been keenly interested in research, writing, and editing. Soon after his graduation, he joined AzoNetwork as a freelancer to sharpen his skills. Ibtisam loves to travel, especially visiting the countryside. He has always been a sports fan and loves to watch tennis, soccer, and cricket. Born in Pakistan, Ibtisam one day hopes to travel all over the world.
Please use one of the following formats to cite this article in your essay, paper or report:
Abbasi, Ibtisam. (2022, October 18). Researchers Create a Spray-Coated Quasi-2D Perovskite Hemispherical Photodetector. AZoM. Retrieved on November 03, 2022 from https://www.azom.com/news.aspx?newsID=60267.
Abbasi, Ibtisam. "Researchers Create a Spray-Coated Quasi-2D Perovskite Hemispherical Photodetector". AZoM. 03 November 2022. <https://www.azom.com/news.aspx?newsID=60267>.
Abbasi, Ibtisam. "Researchers Create a Spray-Coated Quasi-2D Perovskite Hemispherical Photodetector". AZoM. https://www.azom.com/news.aspx?newsID=60267. (accessed November 03, 2022).
Abbasi, Ibtisam. 2022. Researchers Create a Spray-Coated Quasi-2D Perovskite Hemispherical Photodetector. AZoM, viewed 03 November 2022, https://www.azom.com/news.aspx?newsID=60267.
Do you have a review, update or anything you would like to add to this news story?
AZoM speaks with Seokheun “Sean” Choi, a Professor in the Department of Electrical & Computer Engineering at the State University of New York. His new research details the production of a prototype circuit board printed on a sheet of paper.
Dr. Anne Meyer / Dr. Alyson Santoro
In our latest interview, AZoM spoke with Dr. Anne Meyer and Dr. Alyson Santoro who are currently collaborating as part of Nereid Biomaterials. This group is creating a new biopolymer that can be broken down by bioplastic-degrading microbes in marine environments, bringing us closer to reducing the i
This interview discusses how ELTRA, as part of Verder Scientific, produces elemental analyzers for the battery component space.
The BitUVisc is a unique model of viscometer, that can manage highly viscous samples. It is designed to keep the samples warm throughout the entire process.
Discover the FieldLab analyzer, a new, battery-powered, portable oil lab by Spectro Scientific that allows for rapid oil testing in the field.
The BeVision D2 is a dynamic image analyzer that is the perfect choice for the dynamic image analysis of dry powder and granules with its particle range of 30-10,000 microns and ability to analyze 24 different parameters.
This article provides an end-of-life assessment of lithium-ion batteries, focusing on the recycling of an ever-growing amount of spent Li-Ion batteries in order to work toward a sustainable and circular approach to battery use and reuse.
Corrosion is the degradation of an alloy caused by its exposure to the environment. Corrosion deterioration of metallic alloys exposed to the atmosphere or other adverse conditions is prevented using a variety of techniques.
Due to the ever-increasing demand for energy, the demand for nuclear fuel has also increased, which has further created a significant increase in the requirement for post-irradiation examination (PIE) techniques.
AZoM.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2022